Draw-tite 75776 MAX-FRAME RECEIVER Manuel d'utilisateur télécharger pdf (Page 1)

1. Lower and remove spare tire from vehicle. The tire release is located underneath the storage compartment in the back of the vehicle.

2. Remove the access door on rear fascia by removing the two plastic push pins with a #2 phillips screwdriver and pushing the two outside tabs

inward. (Figure 2)

3. Raise hitch into position and insert M12 bolts through the bracket and frame as shown in Figure 1. Note: The plastic bumper locator pin may

interfere with the hitch hardware. If necessary, trim the locator pin at the shoulder to allow proper hardware clearance.

4. Insert M10 bolts through bracket and into the frame as shown in Figure 1 (Hand tighten).

5. Torque M10 bolts first and then M12 bolts to the specifications below.

6. Reinstall spare tire and make sure it is seated properly.

7. Reinstall access door removed in Step 2

Installation Instructions

Hyundai Santa Fe GLS/Limited

(6/7 Passenger)

Part Numbers:

75776

44691

87637

Hitch Shown In Proper Position

Equipment Required: #2 Phillips Screwdriver

Wrenches: 17mm, 19mm

Drill Bits: None

z 2013 Cequent Performance Products, Inc.

Sheet 1 of 3 75776N 4/16/13 Rev. A

Qty. (4) M12 x 1.75 x 120 Bolt CL8.8

Qty. (4) M10 x 1.25 x 30 Bolt CL10.9

Qty. (8) 1/2” Conical Washer

Qty. (4) 7/16” Conical Washer

Qty. (4) M12 x 1.75 Nut CL10

Tighten all M12 CL8.8 fasteners with torque wrench to 72 Lb.-Ft. (98 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75776F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

7000 Lb (3401 Kg) 750 Lb (340 Kg)

Weight Carrying

Ball Mount

5000 Lb (2267 Kg) 750 Lb (340 Kg)

Wiring Access Location: SUV1, SUV2

Fascia

Fasteners typical both sides

Frame rail

2 Existing Weld Nuts

(Typical)

Tighten all M10 CL10.9 fasteners with torque wrench to 40 Lb.-Ft. (54 N*M)

Figure 1

Form: F205 Rev C 9-17-2012

Accessory Rating

jkkl

Plastic Push Pins

Figure 2

Existing Sleeves

Not Shown for Clarity

Access Door

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

1. Lower and remove spare tire from vehicle. The tire release is located underneath the storage compartment in the back of the vehicle. 2. Remove the

Page 2 - Instructions d’installation

jkkl mn 1. Abaisser et enlever le pneu de secours. Le déverrouillage du pneu est situé sous le compartiment à bagages à l'arrière du véhicule. 2.

Page 3 - Instrucciones de instalación

jkkl mn 1. Baje y quite la llanta de repuesto del vehículo. El liberador de la llanta se encuentra debajo del compartimiento de almacenamiento en la p

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 75776 MAX-FRAME RECEIVER Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 75776 MAX-FRAME RECEIVER. Draw-Tite 75776 MAX-FRAME RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Draw-tite 75776 MAX-FRAME RECEIVER Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 75776 MAX-FRAME RECEIVER. Draw-Tite 75776 MAX-FRAME RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 75776 MAX-FRAME RECEIVER