Draw-tite 75555 MAX-FRAME RECEIVER Manuel d'utilisateur télécharger pdf

Installation Instructions

Mitsubishi Outlander

(Except Sport)

Part Numbers:

44579

75555

87444

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 17mm, ¾”

Drill Bits: None

Fastener Kit: 75555F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

4000 (1816 Kg.) 400 (182 Kg.)

Weight Carrying

Ball Mount

4000 (1816 Kg.) 400 (182 Kg.)

Wiring Access Location: SUV3, SUV4

Plastic Fascia

Weldnuts in Vehicle

Frame Rail-Typical

Vehicle Frame

Tow Hook

1. Lower exhaust by disconnecting (3) rubber exhaust hangers from muffler, (2) at the front and (1) at the rear of the muffler.

Note: If additional clearance is needed, disconnect muffler from exhaust pipe by removing (2) bolts forward of muffler. Retain bolts for re-

installation.

2. Raise hitch into position, installing fasteners as shown into existing weldnuts in vehicle frame.

3. Install tube spacer, blocks and ½-13 x 4” lg. hex bolt thru tow hook and into hole in hitch bracket as shown.

Tighten all M10 x 1.25 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

4. Raise exhaust back into position by re-connecting rubber exhaust hangers (re-attach muffler to exhaust pipe if removed in step 1).

Tighten all M10 x 1.25 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

z 2007, 2011 Cequent Performance Products

Sheet 1 of 3 75555N 8-22-11 Rev. C

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Form: F205 Rev A 5-6-05

Qty. (6) Hex Bolt – M10 x 1.25 x 40mm CL8.8

Qty. (1) Block – 3/8 x 1-1/2 x 3

Qty. (6) Conical Washer – 3/8”

Qty. (2) Block – 3/16 x 1-1/2 x 2

Qty. (1) Tube Spacer

Qty. (1) Lockwasher – ½”

Qty. (1) Hex Bolt – ½-13 x 4.00 GR5

Qty. (1) Hex Nut – ½-13

These fasteners typical

Both sides of Vehicle

1 2 3

Résumé du contenu

Page 1 - (Except Sport)

Installation InstructionsMitsubishi Outlander(Except Sport)Part Numbers:445797555587444Hitch Shown In Proper PositionEquipment Required:Wrenches: 17mm

Page 2 - (exception Sport)

Instructions d’installationMitsubishi Outlander(exception Sport)Numéros de pièce :445797555587444Illustration de l'attelage en bonne positionÉqui

Page 3 - (excepto el Deporte)

Instrucciones de instalación Mitsubishi Outlander(excepto el Deporte)Números de partes:445797555587444El enganche se muestra en la posición correcta E

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 75555 MAX-FRAME RECEIVER Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 75555 MAX-FRAME RECEIVER. Draw-Tite 75555 MAX-FRAME RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 75555 MAX-FRAME RECEIVER