Draw-tite 75742 MAX-FRAME RECEIVER Manuel d'utilisateur télécharger pdf

Installation Instructions

Honda CR-V

Part Numbers:

Hitch Shown In Proper Position

Equipment Required: Tape, Utility Knife, Tape Measure &

Marking Pencil, Lubricant or Soapy water

Wrenches: 10mm, 17mm, 11/16,

Small Phillips head Screwdriver,

Existing weld nuts

typical

Fastener Kit: 75742F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Wiring Access Location: SUV3

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

Not For Use With Spring Bars

Weight Carrying

Ball Mount

3500 (1589 Kg) 525 (239 Kg)

75742

87621

44675

Inside isolator

Tie

down

hook

Fascia

Frame rail

17.00

4.25

8.50

3.00

Tape flat

washer to

frame rail

Apperance panel

z 2012 Cequent Performance Products, Inc.

Sheet 1 of 3 75742N 1-25-12 Rev. A

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Form: F205 Rev A 5

Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)

Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)

1. Remove the appearance panel on driver’s side, remove 5-plastic rivets, 3-hex nuts, 2 Phillips head screws located in wheel well behind

the driver’s side rear tire. This panel will need to be trimmed or not reinstalled on vehicle. Ask vehicle owner their choice before starting

installation.

2. Run the (item 1) into existing weld nuts to clear the threads.

3. Reinstall appearance panel if trimmed.

4. Lower exhaust by removing rubber isolators from muffler hangers. Remove the outside isolator first then the inside isolator. Spraying

a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.

5. Tape (item 7) flat washer to rearward weld nut location on both frame rails.

6. Raise hitch into position.

7. Install M10 fasteners as shown.

8. Install the 3/8 U-Bolt through the vehicle tie down hook and through the tie down hook attachment of the receiver. Install flat washer,

lock washers and 3/8 hex nuts as shown above.

9. Tighten all fasteners to the required torque specification.

10. Raise exhaust back into position and re-install rubber isolators.

Note:

Fasteners typical both sides

Exhaust shown lower

Qty. (4) Hex Bolt M10X1.25X30 CL8.8

Qty. (2) Lock Washer

Qty. (4) Conical Washers

Qty. (2) 3/8 Hex Nut

Qty. (1) 3/8-16 U-Bolt

Qty. (2) Flat washer ½”

Qty. (2) Flat Washer 3/8”

17.00

Area to be Trimmed

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

Installation InstructionsHonda CR-VPart Numbers:Hitch Shown In Proper PositionEquipment Required: Tape, Utility Knife, Tape Measure & Marking P

Page 2 - Instructions d’installation

Instructions d’installationHonda CR-VNuméros de pièces :Attelage montré dans la position appropriéeÉquipement requis : Ruban adhésif, couteau à lame r

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónHonda CR-VNúmeros de partes:El enganche se muestra en la posición correcta Equipo necesario: Cinta, cuchillo utilitario C

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 75742 MAX-FRAME RECEIVER Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 75742 MAX-FRAME RECEIVER. Draw-Tite 75742 MAX-FRAME RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 75742 MAX-FRAME RECEIVER