Draw-tite 65029 FRONT MOUNT RECEIVER Manuel d'utilisateur télécharger pdf

Front Mounted Receiver

Installation Instructions

Dodge Dakota 4X4

Dodge Durango 4X4

Part Numbers:

65029

1. Remove plastic shield and return to vehicle owner.

2. If equipped, lower plastic skid plate and notch in area shown above.

3. Remove existing fasteners from bumper brackets.

4. Raise receiver into position and install either M12 hex bolts into existing weldnuts in bumper brackets or if no weldnuts are present use

optional fasteners shown above.

NOTE: Use 1-1/2” x 2” x 1/4” blocks (provided) as spacers between hitch and frame rail if needed.

5. Feed carriage bolts and blocks through access hole in crossmember using pull wire as shown above.

6. Reinstall skid plate if removed in Step 2.

Tighten all 1/2” GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).

Rev. A11/07/05N65029Sheet 1 of 3

z 2005 Cequent Towing Products

Spacer, 1-1/2” x 2” x 1/4”Qty. (10)

Pull Wire, 1/2”Qty. (2)

Carriage Bolt, 1/2”-13 x 2”Qty. (2)

Carriage Bolt, 1/2”-13 x 1-3/4”Qty. (4)

Conical Washer, 1/2”Qty. (6)

Hex Nut, 1/2”Qty. (6)

Hex Bolt, M12 x 1.75 x 45Qty. (4)

Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Tighten all skid plate fasteners with torque wrench to 17 Lb.-Ft (23 N-m).

Equipment Required:

Wrenches: 7/8”, 15mm, 18mm

Drill Bits: None

Fastener Kit: K65029

Hacksaw

Receiver Shown In Proper Position

Remove

Plastic Shield

Bumper

Plastic

Skid

Plate

Bumper Bracket

Existing Weldnuts

Crossmember

Access Hole

Frame

Rail

Notch Skid Plate

In Area Shown

Recovery Eye

Optional

NOTE: All Fasteners Typical

Both Sides Of Vehicle

Optional

Fasteners

CARGO CAPACITY – DO NOT EXCEED

300 LB. OR VEHICLE FRONT GROSS

AXLE WEIGHT RATING. (GAWR)

LB. MAX. WINCH LINE PULL

9000

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

Front Mounted ReceiverInstallation InstructionsDodge Dakota 4X4Dodge Durango 4X4Part Numbers:650291. Remove plastic shield and return to vehicle owner

Page 2 - Instructions d’installation

Récepteur à montage sur l’avantInstructions d’installationDodge Dakota 4X4Dodge Durango 4X4Numéro de pièce :650291. Enlever l’écran en plastique et le

Page 3 - Instrucciones de instalación

Receptor frontalInstrucciones de instalaciónDodge Dakota 4X4Dodge Durango 4X4Números de partes:650291. Retire el protector plástico y devuelva al prop

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 65029 FRONT MOUNT RECEIVER Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 65029 FRONT MOUNT RECEIVER. Draw-Tite 65029 FRONT MOUNT RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 65029 FRONT MOUNT RECEIVER