Draw-tite 65009 FRONT MOUNT RECEIVER Manuel d'utilisateur télécharger pdf

Front Mounted Receiver

Installation Instructions

Jeep Cherokee, Comanche,

Wagoneer (Downsize)

Part Numbers:

65009

1. If present, remove steel skid shield and return to vehicle owner.

2. Remove lower fascia or trim to clear receiver. CONSULT VEHICLE OWNER BEFORE TRIMMING.

3. Lower swaybar bracket on each frame rail.

4. Raise hitch into position and loosely reinstall swaybar bracket as shown above. NOTE: The lip on the underside of the frame rail may need

to be flattened so block can be installed.

5. Using the receiver as a template drill a 1/2” hole as shown above.

6. Feed the remaining fasteners as shown above through slot in the end of the frame rails using pull wire.

Tighten all 1/2” GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).

Rev. A11-07-05N65009Sheet 1 of 3

z 2005 Cequent Towing Products

Spacer, 1” x 2” x 7/16”Qty. (2)

Pull WireQty. (2)

Spacer, 1-1/2” x 2” x 1/4”Qty. (2)

Hex Nut, 1/2”Qty. (2)

Carriage Bolt, 1/2”-13 x 2-1/4”Qty. (2)

Lock Washer, 1/2”Qty. (2)

Conical Washer, 3/8”Qty. (4)

Flat Washer, 1/2”Qty. (2)

Hex Bolt, M10 x 1.50 x 35Qty. (4)

Tighten all M10 CL10.9 fasteners with torque wrench to 42 Lb.-Ft (57 N-m).

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Wrenches: 15mm, 7/8”

Equipment Required:

Drill Bits: 1/2”

Hammer

Fastener Kit: K65009

CARGO CAPACITY – DO NOT EXCEED

300 LB. OR VEHICLE FRONT GROSS

AXLE WEIGHT RATING. (GAWR)

LB. MAX. WINCH LINE PULL

9000

Receiver Shown In Proper Position

Bumper

Lower

Fascia

Swaybar Bracket

Existing Weldnuts

Drilled Hole

Recovery

Eye

Lip

Frame Rail

Slot

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

Front Mounted ReceiverInstallation InstructionsJeep Cherokee, Comanche,Wagoneer (Downsize)Part Numbers:650091. If present, remove steel skid shield an

Page 2 - Instructions d’installation

Récepteur d’attelage à montage sur l’avantInstructions d’installationJeep Cherokee, Comanche,Wagoneer (Downsize)Numéro de pièce :650091. Si elle est p

Page 3 - Wagoneer (tamaño reducido)

Receptor frontalInstrucciones de instalaciónJeep Cherokee, Comanche,Wagoneer (tamaño reducido)Números de partes:650091. Si está presente, retire el pr

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 65009 FRONT MOUNT RECEIVER Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 65009 FRONT MOUNT RECEIVER. Draw-Tite 65009 FRONT MOUNT RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 65009 FRONT MOUNT RECEIVER