Draw-tite 75527 MAX-FRAME RECEIVER Manuel d'utilisateur télécharger pdf

Installation Instructions

Toyota Tundra

Part Numbers:

75527 44568

87434 78222

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 17mm, 19mm, 22mm, 3/4, 7/8

Drill Bits: None

Tighten all M14 X 2.00 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)

z 2011 Cequent Performance Products

Sheet 1 of 3 75527N 4/18/11 Rev. B



Qty. (4) M12 X 1.25 CL9.8 X 40mm Hex Bolt



Qty. (4) M14 Hex Nut



Qty. (6) Conical Toothed Washer



Qty. (2) 1/2-13 X 1.75 Hex Bolt



Qty. (4) M14 X 2.00 CL10.9 X 40mm



Qty. (2) 1/4 X 1.00 X 2.00 Block



Qty. (4) 5/8 Flat Washer



Qty. (2) 1/2 Hex Nut



Qty. (4) 5/8 Lock Washer

Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75527F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

8000 (3632 Kg) 800 (363 Kg)

Weight Carrying

Ball Mount

6000 (2724 Kg) 600 (272 Kg)

Wiring Access Location: PU3

Form: F205 Rev A 5-6-05

1. Remove angle brackets from the inside surface between the frame rails and the bumper brackets.

2. Raise hitch into position and install M12 bolts and conical toothed washers into existing weldnuts.

3. Install M14 bolts through the vehicle bumper bracket, through the hitch and fasten with flat washer, lock washer, and hex nut.

4. Install 1/2-13 hex bolts and 1/4 block through the bumper bracket, through the hitch and fasten with conical toothed washers

and hex nuts.

5. Tighten all fasteners to the required torque specifications.

Tighten all M12 X 1.25 CL9.8 fasteners with torque wrench to 105 Lb.-Ft. (142 N*M)

Bumper Bracket

Frame Rail

Angle Bracket

Both Sides

Existing Weldnuts

Fasteners Typical Both Sides

Bumper

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

Installation Instructions Toyota Tundra Part Numbers: 75527 44568 87434 78222 Hitch Shown In Proper Position Equipment Required: Wrenches: 17mm, 19mm

Page 2 - Instructions d’installation

Instructions d’installation Toyota Tundra Numéros de pièces : 75527 44568 87434 78222 Attelage montré dans la position appropriée Équipement requis :

Page 3 - 87434 78222

Instrucciones de instalación Toyota Tundra Números de partes: 75527 44568 87434 78222 El enganche se muestra en la posición correcta Equipo necesari

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 75527 MAX-FRAME RECEIVER Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 75527 MAX-FRAME RECEIVER. Draw-Tite 75527 MAX-FRAME RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 75527 MAX-FRAME RECEIVER