Draw-tite 36535 FRAME HITCH Manuel d'utilisateur télécharger pdf

Installation Instructions

Lexus GS350

Part Numbers:

36535

90232

06945

Hitch Shown In Proper Position

Equipment Required: Utility Knife, Marker,

Tape measure, body panel tool

Wrenches: 10mm socket, 12mm socket,

Ratchet, 6” socket extension

Phillips screw driver, Flat screw driver

z 2013 Cequent Performance Products, Inc.

Sheet 1 of 2 36535N 12-6-13 Rev C

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 36535F

Wiring Access Location: PC3, PC4

Form: F205 Rev A 5-6-05

Tighten all M8-1.25 CL10.9 fasteners with torque wrench to 25Lb.-Ft. (34 N*M)

IMPORTANT NOTE! The bumper cover requires trimming to install hitch. Consult with vehicle owner before proceeding with install.

1. Remove bumper cover (Fascia) by removing (1) screw from behind rear tire at bottom of fascia, both sides

2. Next, remove (1) screw hidden behind inner wheel well at the top of the fascia. Remove the plastic clip by pulling center out

with a flat screw driver, both sides.

3. Open trunk lid and remove small round plastic panel located between tail light and trunk opening. Remove the screw, both

sides.

4. Remove center (4) push fasteners from the rear underside of the fascia, using a flat screw driver.

5. Carefully remove bumper cover, starting with the sides first. Use a plastic body panel tool to separate the plastic fascia along

the seam. Note: Unplug back-up sensor wiring. (continued page 2)

Vehicle End

Panel

Figure 2.

Figure 1.

Vehicle fascia

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

3500 Lb. (1589 kg) Max Gross Trailer Weight

300 Lb. (136 kg) Max Tongue Weight

Drawbar must be used in the

Rise position only.

Drawbar Kit:

36071

(All models)

3-1/8”

1-1/2”

Bottom View of Bumper Cover

Accessory Rating

Printed in Mexico

Vehicle M8

factory bolts

1 2 3 4 5 6

Résumé du contenu

Page 1 - Installation Instructions

Installation InstructionsLexus GS350Part Numbers:365359023206945Hitch Shown In Proper PositionEquipment Required: Utility Knife, Marker, Tape measure

Page 2

Installation InstructionsLexus GS350 (All Models)36535Nz 2013 Cequent Performance Products, Inc.Sheet 2 of 2 36535N 12-6-13 Rev CNote: check hitch fre

Page 3 - Instructions d’installation

Instructions d’installationLexus GS350Numéros de pièce :365359023206945Attelage montré dans la position appropriéeÉquipement requis : Couteau utilitai

Page 4

Instructions d’installationLexus GS350 (tous les modèles)36535Nz 2013 Cequent Performance Products, Inc.Feuille 2 de 2 36535N 12-6-13 Rev. CNota : Vér

Page 5 - Instrucciones de instalación

Instrucciones de instalaciónLexus GS350Números de partes:365359023206945El enganche se muestra en la posición correctaEquipo necesario: Cuchillo utili

Page 6

Instrucciones de instalaciónLexus GS350 (Todos los modelos) 36535Nz 2013 Cequent Performance Products, Inc.Hoja 2 de 2 36535N 12-6-13 Rev. CNota: Revi

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 36535 FRAME HITCH Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 36535 FRAME HITCH. Draw-Tite 36535 FRAME HITCH User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 36535 FRAME HITCH