29 3/4”
5.5’, 6.5’, 8’ Bed
Measure from rear edge of
truck bed to rear edge of
base rail.
Front of
Vehicle
Rear Edge of
Truck Bed
ROW
1
ROW 2
ROW 3
ROW 4
3” Carriage bolt &
tube spacer
Drill through top of
frame (both sides)
3” Carriage bolt, 1/2” spacers &
bevel washers
Drill through top of frame
See Detail Inside Frame
Use rear
center hole
only in rear
base rail
1-3/4” carriage bolt with
short bracket
Base rail must
have a bolt in
either of the
marked center
holes. Check for
obstructions
before drilling.
1-3/4” carriage
bolt with long
bracket
1-3/4” carriage
bolt with long
bracket
2007 And Newer Toyota Tundra 6.5’ & 8’ Beds (Crewmax 5.5’ Bed requires Sidewinder Pinbox Coupler)
CAUTION!
Read pages 2-3 of 30035 instructions before starting installation. Failure to do so could result in significant vehicle damage!
CAUTION!
Check for obstructions before drilling. Failure to do so could result in damaged fuel or brake lines, structural members, etc. REESE
PRODUCTS does its best to communicate tow vehicle manufacturer changes; however, it is ultimately the responsibility of the installer to
prevent damage due to installation.
IMPORTANT NOTES FOR THIS INSTALLATION:
1. Use the 58309 service kit together with the 30035 mounting kit. Read p. 1-3 of the 30035 instruction for general
information.
2. The mounting holes for Row 3 go through the inside of the bed sill. Make sure it lines up correctly. Drill through
the bed and the top of the frame on both sides. For the Row 4 passenger side attachment, drill through the bed
and the top of the frame as well.
3. The rear rail on the passenger side is secured directly to the frame with 3” carriage bolts provided in the 58309
kit. For the Row 3 attachment 2, a tube spacer should be placed inside the bed sill on top of the frame and
under the bottom of the bed. Line up the spacer with the drilled hole before inserting the carriage bolt. Repeat
for both sides. See Detail Inside Frame.
Short bracket
Bed Sill
* Optional weld
pattern
*
1/4 2
1/4 2
Axle Center
King pin center approx. 3-1/2”
forward of axle center
Long bracket
Tube spacer
inside bed sill
*
1/4 1.5-3
1/4 2
4. For the Row 4 passenger side
attachment, stack two 1/2”
spacers and a bevel washer,
provided in the 58309 kit, to fill
the gap between the bed and the
frame. Use another bevel washer,
conical toothed washer, and hex
nut to fasten the 3” carriage bolt
in place. See Detail Inside
Frame.
5. Install the long brackets on the
front rail and the short bracket on
the rear rail driver side using the
1-3/4” carriage bolts provided in
the 58309 kit. All other
attachments to the bed use 2”
carriage bolts from the 30035 kit.
Vehicle Forward
Rear Passenger Side
Detail Inside Frame
3” Carriage Bolts
Tube spacer
inside bed sill
bevel
washer
1/2” spacers (2),
bevel washer
Do not install on a
truck with a 5’7” long
bed unless the trailer
is equipped with a
Sidewinder Pinbox
Coupler.
©2007, 2008, 2009 Cequent Performance Products 58309N 2-6-09 Rev. B
(18 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels