Draw-tite 41534 MAX-E-LOADER RECEIVER Manuel d'utilisateur télécharger pdf

Installation Instructions

CHEVROLET SILVERADO PICKUP

GMC SIERRA PICKUP

(Vehicles with amber turn signals)

Part Numbers:

41534

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 13/16, 7/8, 15/16, 21mm

Drill Bits: None

Figure 1

Note: On vehicles without factory bumper, it may be necessary to relocate license plate mounting bracket

1. Remove existing M14 bolts from end of each frame rail.

2. Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.

Note: For vehicles w/o bumper, locate slots in receiver over fore/aft slot near end of frame.

3. Reinstall existing M14 bolts through receiver and frame into existing weldnuts.

Note:

For vehicles w/o bumper, locate slots in receiver over fore/aft slot near end of frame.

See Figure 2 for placement of fasteners on vehicles w/o bumper.

4. Install remaining fasteners as shown.

Rev. A5-18-06N41534Sheet 1 of 3

z 1998, 1999, 2000, 2002, 2006 Cequent Towing Products

SpacerQty. (2)

Hex Nut 1/2-13Qty. (6)

Hex Nut 9/16-12Qty. (2)



SpacerQty. (4)

Lock WasherQty. (2)

Conical WasherQty. (6)

Flat WasherQty. (2)

Spacer .25 X 1.50 X 3.00Qty. (2)

Bolt 9/16-12 X 1.75 Qty. (2)

Carriage Bolt 1/2-13 X 1.75Qty. (6)

Tighten all 9/16 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: F41534

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

600 (272 Kg)6000 (2724 Kg)

Weight Carrying

Ball Mount

1200 (545 Kg)12,000 (5448 Kg)

Weight Distributing

Max Tongue

WT (LB)

Max Gross

Trailer WT (LB)

Hitch type

Wiring Access Location: PU3

Tighten all 9/16 GR5 fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)

Figure 2

Bumper bracket

Existing weldnut

Step bumper

Note: Fasteners typical both sides

Tighten all M14 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)

Required for vehicles

without bumpers

Required for vehicles

without bumpers

*Note: Orientate short side

of block against frame as

shown

Frame



Existing M14 fastener

Form: F205 Rev A 5-6-05

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

Installation InstructionsCHEVROLET SILVERADO PICKUPGMC SIERRA PICKUP(Vehicles with amber turn signals)Part Numbers:41534Hitch Shown In Proper Position

Page 2 - Form: F205 Rev A 5-6-05

Instructions d’installationCHEVROLET SILVERADO PICKUPGMC SIERRA PICKUP(Véhicules avec les signaux ambres de tour)Numéros de pièces :Barre de remorquag

Page 3

12151534349876Instrucciones de instalaciónCHEVROLET SILVERADO PICKUPGMC SIERRA PICKUP(vehículos con las señales ambarinas de la vuelta)Números de par

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 41534 MAX-E-LOADER RECEIVER Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 41534 MAX-E-LOADER RECEIVER. Draw-Tite 41534 MAX-E-LOADER RECEIVER User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 41534 MAX-E-LOADER RECEIVER