Draw-tite 36465 FRAME HITCH Manuel d'utilisateur télécharger pdf

Installation Instructions

Kia Amanti

Part Numbers:

Hitch Shown In Proper Position

Wiring Access Location: PC3,4

Equipment Required: Phillip’s head screwdriver,

Lubricant or Soapy water

Wrenches: 10mm, 12mm, 17mm, 11/16”

1. Lower exhaust rubber isolator front and rear of muffler. Remove (2) nuts holding rear muffler hanger. Note: Spraying a lubricant or soapy

water on the metal hanger rod and the rubber isolator helps removal.

2. Remove appearance panel which covers the trunk pan (for ease of hitch installment). Remove the (4) plastic rivets that fasten the fascia tabs

to the vehicle. Note: Remove the center of the rivet with a screwdriver. Rivets to be reinstalled.

3. Hang U-bolt on tow hook

4. Slide hitch up over exhaust tips and align hole in side arm of hitch with weld nuts in vehicle frame as shown in above.

5. Re-install appearance panel.

6. Loosely install U-Bolt

7. Tighten all fasteners to torque specifications.

8. Raise exhaust system back into position.

Rev. X10-19-0736465NSheet 1 of 3

z 2007 Cequent Towing Products

Hex nut 3/8-16Qty. (2)

U-Bolt 3/8-16Qty. (1)

Lock washerQty. (2)

Conical washerQty. (2)

Flat washerQty. (2)

Hex bolt M10 X 1.25 X 40mm CL8.8Qty. (2)

Tighten all 3/8 GR2 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)

Tighten all M10 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE

position only.

Drawbar Kit:

36061

Fastener Kit: 36465F

36465

90170

06607

Note: Fasteners typical

both sides

3500 LB (1589 Kg) Max Gross Trailer Weight

300 LB (136 Kg) Max Tongue Weight

Frame rail

Muffler

Remove (2) nuts

holding rear muffler

hanger.

Remove exhaust rubber

isolator front of muffler.

Existing

weld nut

Heat shield, exhaust hangers and

wheel well not shown for clarity.

Frame rails

Muffler

Form F206 Rev A 5605

1 2 3

Résumé du contenu

Page 1 - Kia Amanti

Installation InstructionsKia AmantiPart Numbers:Hitch Shown In Proper PositionWiring Access Location: PC3,4Equipment Required: Phillip’s head screwdri

Page 2 - Instructions d’installation

Instructions d’installationKia AmantiNuméros de pièces :Attelage montré dans la position appropriéePoint d’accès au câblage : PC3,4Équipement requis :

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónKia AmantiNúmeros de partes:El enganche se muestra en laposición correctaUbicación del acceso al cableado: PC3,4Equipo nec

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 36465 FRAME HITCH Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 36465 FRAME HITCH. Draw-Tite 36465 FRAME HITCH User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 36465 FRAME HITCH