Draw-tite 24912 SPORTFRAME HITCH Manuel d'utilisateur télécharger pdf

Installation Instructions

Mazda 3 sedan

Part Numbers:

24912

60344

77299

Hitch Shown In Proper Position

Wiring Access Location: PC3, 4

Equipment Required:

Wrenches: 11/16

Drill Bits: None

Frame rail

Printed in Mexico

Note: if additional clearance is needed for installation. Lower exhaust system at the rubber isolators. Spraying a lubricant on the metal hanger rod

and the rubber isolator helps removal.

1. Raise the hitch into position, feed the pull wires though the adjacent slots on the hitch.

2. Feed the pull wire into the rearward slot and out the access hole. Attach spacer and carriage bolt to pull wire and feed into frame rail, pull into

position. Both sides. See Figure 2. Leave pull wire attached.

3. Using the reverse pull wire procedure Figure 3. Feed the pull wire into position both rails. Leave pull wires attached.

4. Carefully remove pull wires. One at a time place the washer over the pull wire and use it to hold the bolt in place while carefully removing the

pull wire, then attach the hex nut.

5. Tighten all fasteners to the required torque specification.

z 2013 Cequent Performance Products

Sheet 1 of 3 24912N 11-1-13 Rev. A

Qty. (4) Carriage bolt 7/16-14 X 1.50 GR5

Qty. (4) Hex nut 7/16-14

Qty. (4) Spacer 1/4” X 7/8” X 3”

Qty. (4) Pull wire 7/16”

Qty. (4) Conical tooth washer 7/16”

Tighten all 7/16-14 Gr5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE position only.

Drawbar Kit:

3593

Fastener Kit: 24912F

Form F206 Rev B 9

2012

Accessory Rating

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Note: Fasteners typical

both sides

Access

hole

Kink pull wire to keep

spacer independent of bolt

Frame rail

Fascia

Access

hole

Forward

slot

Rearward

slot

Forward

Reverse pull wire procedure

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

Installation InstructionsMazda 3 sedanPart Numbers:24912 60344 77299Hitch Shown In Proper PositionWiring Access Location: PC3, 4Equipment Req

Page 2 - Instructions d’installation

Instructions d’installationMazda 3 sedanNuméros de pièce :24912 60344 77299Attelage montré dans la position appropriéePoints d'accès au

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónMazda 3 sedanNúmeros de partes:24912 60344 77299El enganche se muestra en la posición correctaUbicación del acces

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 24912 SPORTFRAME HITCH Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 24912 SPORTFRAME HITCH. Draw-Tite 24912 SPORTFRAME HITCH User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 24912 SPORTFRAME HITCH