Draw-tite 24839 SPORTFRAME HITCH Manuel d'utilisateur télécharger pdf (Page 1)

1. Lower exhaust by removing the rubber exhaust hanger.

2. Remove the inner wheel well and splash guards from vehicle, both sides.

3. Remove tow hook from passenger’s side frame rail and return to vehicle owner.

4. Raise hitch into position and loosely install the M10 bolts and conical toothed washers as shown.

5. Pull hitch rearward and tighten all fasteners using a torque wrench as specified below.

6. Reinstall muffler hanger.

7. Reinstall the inner wheel well and splash guards.

Tighten all M10 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)

INNER WHEEL WELL / SPLASH GUARD

REMOVE FASTENERS

Installation Instructions

Kia Soul

Part Numbers:

24839

60256

24792 (U-Haul)

77230

Hitch Shown In Proper Position

Wiring Access Location: SUV1, SUV2

Equipment Required: Torque wrench

Wrenches: 17mm Socket and Ratchet Wrench

Phillips screw driver

Drill Bits: None

2000 LB (908 Kg.) Max Gross Trailer Weight

200 LB (90.8 Kg.) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE position only.

Drawbar Kit:

3593

Fastener Kit: 24839F

Fascia

Qty. (4) Hex Bolt, M10 x 1.25 x 30mm CL8.8

Qty. (4) Conical Toothed Washer 3/8”

z 2009, 2012, 2013 Cequent Performance Products – Printed in México

Sheet 1 of 3 24839N 12-16-13 Rev. F

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

EXISTING WELDNUTS

Accessory Rating

1 2 3

Résumé du contenu

Page 1 - Installation Instructions

121. Lower exhaust by removing the rubber exhaust hanger.2. Remove the inner wheel well and splash guards from vehicle, both sides.3. Remove tow hook

Page 2 - Instructions d’installation

121. Abaisser l'échappement en enlevant le support d'échappement en caoutchouc.2. Enlever le passage de roue intérieur et les bavettes garde

Page 3 - Instrucciones de instalación

121. Baje el escape quitando el gancho de goma. 2. Retire de ambos lados del vehículo el receptáculo de rueda interno y los protectores de salpicadura

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 24839 SPORTFRAME HITCH Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 24839 SPORTFRAME HITCH. Draw-Tite 24839 SPORTFRAME HITCH User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Draw-tite 24839 SPORTFRAME HITCH Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 24839 SPORTFRAME HITCH. Draw-Tite 24839 SPORTFRAME HITCH User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 24839 SPORTFRAME HITCH