Draw-tite 24754 SPORTFRAME HITCH Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 24754 SPORTFRAME HITCH. Draw-Tite 24754 SPORTFRAME HITCH User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 3
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Installation Instructions
MITSUBISHI ECLIPSE
Part Numbers:
24754, 77130,
60813, 24842
U-Haul
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
FASCIA
TRUNK
PAN
BRACKET
Hitch Shown In Proper Position
Wiring Access Location: PC3 , PC4
Equipment Required:
2000 LB Max Gross Trailer Weigh
t
200 LB Max Tongue Weight
Fastener Kit: 24754F
ANGLE
BRACKET
Wrenches: 10mm, 11/16”
Drill Bits: 15/32 (.469)
Drawbar Kit:
DRILL HOLE
DRILL HOLE
DRILL
HOLES
1
Qt (4)
Ci Blt7/16
14 X 1 50
5
Qt (1)
Ci Blt7/16
14 X 2 50
Drawbar must be used in the
RISE
position only.
3597
6806
REMOVE SPARE TIRE
BEFORE DRILLING
1. Remove spare tire. Remove the drain plug from the passenger side of the trunk.
2. Put the angle bracket (1) with carriage bolt (Item 1) over the existing drain hole inside the trunk setting against the bottom and back of the trunk
pan.
1
Qt
y.
(4)
C
arr
i
age
B
o
lt
7/16
-
14
X
1
.
50
5
Qt
y.
(1)
C
arr
i
age
B
o
lt
7/16
-
14
X
2
.
50
2
Qty. (5) Flat Washer 7/16
6
Qty. (1) Block 1 x 2
3
Qty. (5) Lock Washer 7/16
7
Qty. (2) Block 1 x 2
4
Qty. (5) Hex Nut 7/16-14
8
3. Raise the hitch into position under the angle bracket and attach the fasteners as shown. Hand tighten the hitch to angle bracket fasteners.
4. Align the hitch into position using the back of the trunk pan and the rib running along the trunk pan with the location of the hole on the hitch
bar. Check the location of the hitch on the vehicle. Note: center rib on trunk pan not center of vehicle.
5. Drill the hole thru the rib and into the trunk using the hitch as a template. Secure the hitch using the fasteners as shown.
6. Drill a hole using the hitch as a template into the trunk pan on the drivers side of the vehicle. Repeat step 2. Hand tighten all fasteners.
7. With the hitch in position and both angle brackets setting against the rear of the trunk pan drill the holes thru the rear of the trunk pan using the
angle brackets as a template. Place the (2) remaining (Item 1) Carriage bolt through the angle brackets.
8. Remove the (2) bolts with the 10mm wrench and push the fascia out of the way to allow access to the rear of the trunk pan and fastener.
Attach the fasteners as shown.
9. Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft.
10. Seal drilled or existing drain holes in trunk pan to prevent intrusion of exhaust fumes and water
11. Reinstall the spare tire in the trunk and re-attach the fascia.
z 2005, 2010 Cequent Performance Products
Sheet 1 of 3 24754N 6-9-10 Rev. C
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Vue de la page 0
1 2 3

Résumé du contenu

Page 1 - Installation Instructions

Installation InstructionsMITSUBISHI ECLIPSEPart Numbers:24754, 77130,60813, 24842 U-HaulDo Not Exceed Lower of Towing Vehicle Manufacturer’s Rating o

Page 2 - Instructions d’installation

Instructions d’installationMITSUBISHI ECLIPSENuméro de pièce:Ne pas excéder les spécifications du fabricant de véhicules de remorquage, ouCARÉNAGETÔLE

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónMITSUBISHI ECLIPSENúmero de partes:El enganche se muestra en laNo supere el valor inferior entre la calificación del fabri

Commentaires sur ces manuels

Pas de commentaire