WARNING
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer
once installed. For initial test, reset vehicle
electrical system by temporarily removing
the key from the ignition.
9. Near center of vehicle, below trunk threshold,
clean a flat area using a mixture of rubbing
alcohol and water. Mount the T-Connector
black box using double-sided tape provided.
10. Secure the remainder of the T-Connector
harness with the cable ties provided, to
prevent damage or rattling and being careful
to avoid any areas that would pinch, cut or
melt the wire.
11. Replace carpet, and any other clips or panels
that were removed during installation being
careful not to cut or pinch the wires.
NOTE
Store 4-Flat in trunk area when not in use.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Drill (3/32” Drill Bit),
Philips Head Screwdriver, Test-probe
1. Open trunk. Temporarily remove the rear
threshold plate. Partially remove the felt
trunk liner behind the taillights
de
.
2. On the driver and passenger sides of the
vehicle, locate the vehicle’s taillight wiring
harness. The taillight wiring harness will have
a connection point, on both sides, matching
the ends of the T-Connector. Separate this
connector, being careful not to break the
locking tabs. All connector surfaces should
be clean and free of dirt.
3. On the driver’s side, insert the T-Connector
end, with the yellow wire, between the
vehicle wiring connectors and lock into place.
Be careful not to damage the locking tabs and
be sure that connectors are fully inserted with
locking tabs in place.
4. Route the T-Connector end with green
wire to the passenger ‘s side behind the
panels and along the threshold. Repeat step
3 using the T-Connector ends containing the
green wire
f
.
5. Locate a suitable grounding point near the
connector. Clean dirt and rustproofing from the
area. Drill a 3/32” hole and secure the white
wire using the eyelet and screw provided.
CAUTION
Verify what is behind any surface prior to
drilling to avoid damage to the vehicle and/
or personal injury. Do not drill into any
exposed surfaces.
6. From inside the vehicle, connect the black
12 ga. wire and the red wire from the
T-Connector black box with the supplied
yellow butt connector. Either route the black
wire thru a grommet and along the exterior
frame or follow the existing wiring along the
thresholds into the engine compartment up to
the battery avoiding areas that may pinch or
break the wire
g
.
WARNING
If routing the wire thru a grommet and along
the exterior of the vehicle, be careful to avoid
any hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
7. Disconnect the vehicle’s Negative (-) battery
cable. If not removed, remove the fuse from
the yellow fuse holder (provided). After cutting
the fuse holder wire
h
, attach the ring
terminal and secure to the vehicle’s Positive
(+) battery cable
i
. Connect the other end
of the fuse holder to the black 12 ga. wire,
using the yellow butt connector (provided).
WARNING
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
8. Reconnect the vehicle’s Negative (-) battery
cable and install the 10 amp fuse into the
fuse holder from step 7
j
.
READ THIS FIRST:
Read and follow all vehicle warnings and
installation instructions before beginning installation.
Wear safety glasses and use all safety precautions
during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes
de protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones
de instalación del vehículo antes de empezar la
instalación. Use gafas de seguridad y todas las
precauciones de seguridad durante la instalación.
118576-037 Rev. A 12/11/2012
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Malibu
d
e
g
f
h
i
j
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels