Draw-tite 59762 ROOF RACK Manuel d'utilisateur télécharger pdf

PART No:

Fitting Instructions

APE (Anchor Point Extended)

Cross Bar Kits

CARRYING CAPACITY:

Pg 1 of 2

50Kgs/

110 Lbs

Printed in China

Note: Prior to Assembly

Prior to assembling your cross bar kit check

that the kit contains all the parts you will need

to fit the cross bars. Refer to parts lists for

guidance.

Please read these instructions before assembly.

Step 1: Opening the vehicles anchor point doors.

On the vehicles roof or ditch molding you will find fore

and aft anchor point doors (fig 1).

Carefully open these doors by inserting a plastic tool in

the notch and prying the door open as shown. This will

reveal the anchor points. It is advisable to screw the

bolts into the anchor point threads at this time to clean

the threads.

Note: Take care when opening the doors to avoid

damaging the doors and the vehicles finish. Doors will

remain open and attached to vehicle while the cross bars

are on the vehicle.

Step 2: Installing Rubber Gaskets and Adaptor

Position the rubber gaskets over the anchor points

and the Anchor point door. Orient the curved relief

opening towards the outside of vehicle and centered

over the anchor point threads in the roof as shown in

(fig 2).

Ensure that the gasket is properly aligned.

If your gasket has a directional arrow this always

points toward the front of vehicle.

Place the plastic adaptors into the gasket’s recessed

top surface (fig 3).

Cross Bars

End support

Plastic adaptor

Rubber Gasket

M8 x 20mm Bolt

Clamp plate

M8 spring washer

M8 washer

L wrench

M6 x 45mm bolt

M8 hex nut

Cross bar end

caps

Tool required – 13mm or adjustable wrench

Anchor point

door

Vehicle’s

roof

Anchor point

Plastic adaptor

Vehicle’s roof

Anchor point

Rubber Gasket

Front of

vehicle

Vehicle’s roof

Location of anchor points on vehicle

Fig. 1

Fig. 2

Fig. 3

Parts list

End cap key

59761-4N REV 5-3-12

59761-4N

Under Cover

Curved relief to

outside of vehicle

1 2 3 4 5 6

Résumé du contenu

Page 1 - Cross Bar Kits

PART No: Fitting Instructions APE (Anchor Point Extended) Cross Bar Kits CARRYING CAPACITY: Pg 1 of 2 50Kgs/ 110 Lbs Printed in China Not

Page 2

PART No: 59761-4N REV 5-3-12 Fitting Instructions APE (Anchor Point Extended) Cross Bar Kits CARRYING CAPACITY: Pg 2 of 2 50Kgs/ 110 Lbs

Page 3 - Lista de partes

Número de parte: Instrucciones de ajuste APE (Punto de anclaje Extendido) Kit de travesaños CAPACIDAD DE CARGA: Pg 1 de 2 50 Kgs / 110

Page 4

PARTE No: Instrucciones de ajuste APE (extendido desde punto de anclaje) Kits de travesaños CAPACIDAD DE CARGA: Pg 2 de 2 50Kgs/ 110 Lbs Imp

Page 5 - Nomenclature des pièces

No PIÈCE : Instructions de montage Allongement des points d'ancrage Ensembles de traverses de toit Capacité de charge : Pg 1 de 2 50 k

Page 6 - Pg 2 de 2

No PIÈCE : Instructions de montage APE (Anchor Point Extended - Allongement des points d'ancrage) Ensembles de traverses Capacité de charge

Commentaires sur ces manuels

Pas de commentaire

Draw-tite 59762 ROOF RACK Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Draw-tite 59762 ROOF RACK. Draw-Tite 59762 ROOF RACK User Manual [en] [ru] [de] [es] [fr] [it] [pl] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Draw-tite 59762 ROOF RACK